Hydraulics likely cause of loose clutch pedal |

Hydraulics likely cause of loose clutch pedal

Q It’s been awhile since you helped me with my Toyota 4×4 truck starter. All has been going well with the new starter and the rest of the truck. A new problem just began this week. I went to start my truck, and the clutch pedal nearly went to the floor before I felt any resistance. I could get the truck into gear, both forward and reverse, and drive it without trouble or noise; it just felt strange to suddenly have so much free play in the clutch pedal before engaging each time.

The week before, the clutch pedal felt normal and shifting was not a problem — no grinding or difficulty getting it into gear. The pedal free play was normal, too. Then the sudden change in the pedal after not driving it for a week. So I checked the clutch cylinder fluid reservoir, and it was full. There are no leaks inside or outside the cylinder. I checked under the truck, and the slave cylinder looks dry. The line looks dry too.

Did my clutch suddenly go while sitting in my driveway? Or is it time to flush and replace the fluid and hope that will bring it back to normal? The truck has a lot of miles on it, and I don’t know when the clutch was ever replaced. What else should I check before deciding whether a costly new clutch is needed? The truck is a 4×4 and I think it’s beyond my skill set to do a clutch myself.

— Jen

A Great job, again, describing details and performing spot-on inspections — you’d make a super technician. Your truck, like most modern stick-shift vehicles, uses a hydraulic process to connect clutch pedal motion to the clutch mechanism within the transmission bell housing. As the pedal is depressed, a pushrod applies force to the clutch master cylinder, pushing a piston about 1 inch. Hydraulic force is applied, via fluid through a steel or plastic line, to the slave cylinder, which is bolted to the bell housing. The slave cylinder piston moves similarly, and a second pushrod applies force to the clutch fork. This process is infinitely smoother and usually less trouble than the cable or lever mechanisms used in the past.

Since your clutch releases OK, even with lots of pedal free play, and doesn’t slip, it should be fine. A worn-out clutch typically releases (and may slip) near the top of pedal travel, or in the case of a warped disc or failed pressure plate, may not release completely, even when depressed fully, causing gear clash.

Your symptoms sure seem to point to a hydraulic issue, which should be fairly easy to fix. I’m thinking a layer of sludge in the bottom of the fluid reservoir may be preventing the master cylinder from receiving a fresh gulp of fluid, or the master cylinder may have begun to leak internally, back to the reservoir.

Does pedal free play decrease if you pump it repeatedly? This would further verify the fault as being hydraulic in nature. Did you look for leakage inside the truck, above and in front of the pedal? Many times, a faulty clutch master cylinder will leak inside the truck, rather than down the front of the firewall.

I’d try swabbing out the bottom of the reservoir and refilling fluid by bleeding the system.

Brad Bergholdt is an automotive technology instructor at Evergreen Valley College in San Jose, Calif. Readers may send him email at [email protected]; he cannot make personal replies

TribLIVE commenting policy

You are solely responsible for your comments and by using you agree to our Terms of Service.

We moderate comments. Our goal is to provide substantive commentary for a general readership. By screening submissions, we provide a space where readers can share intelligent and informed commentary that enhances the quality of our news and information.

While most comments will be posted if they are on-topic and not abusive, moderating decisions are subjective. We will make them as carefully and consistently as we can. Because of the volume of reader comments, we cannot review individual moderation decisions with readers.

We value thoughtful comments representing a range of views that make their point quickly and politely. We make an effort to protect discussions from repeated comments either by the same reader or different readers

We follow the same standards for taste as the daily newspaper. A few things we won't tolerate: personal attacks, obscenity, vulgarity, profanity (including expletives and letters followed by dashes), commercial promotion, impersonations, incoherence, proselytizing and SHOUTING. Don't include URLs to Web sites.

We do not edit comments. They are either approved or deleted. We reserve the right to edit a comment that is quoted or excerpted in an article. In this case, we may fix spelling and punctuation.

We welcome strong opinions and criticism of our work, but we don't want comments to become bogged down with discussions of our policies and we will moderate accordingly.

We appreciate it when readers and people quoted in articles or blog posts point out errors of fact or emphasis and will investigate all assertions. But these suggestions should be sent via e-mail. To avoid distracting other readers, we won't publish comments that suggest a correction. Instead, corrections will be made in a blog post or in an article.