ShareThis Page
Wheel alignment key to wear |

Wheel alignment key to wear

Brad Bergholdt
| Friday, December 6, 2013 10:07 p.m

Question: I just had new tires installed on my car. The place recommended a wheel alignment and said my new tires would last longer if I had this done. I agreed, then they called me back later and said I need some parts replaced or they couldn’t align it. I passed on the work and am now back driving with new tires and no alignment. I’m wondering what to do now. The car doesn’t shake and my tires lasted a fair distance. What does an alignment entail, and why can’t it be done?

— Holly P.

Answer: Wheel alignment is important for proper tire wear and straight, stable tracking. Older, rear-wheel drive vehicles required only a periodic front wheel alignment (check and/or adjustment), while front-wheel and many all-wheel drive vehicles may have adjustable components in the rear as well. Imagine the human body with very loose knees and/or ankles, or a bent femur or tibia. Your tennis shoes would likely scuff and skid a bit more than planned as you walked.

The three principal front-wheel alignment angles are caster, camber and toe. Adjustable rear suspensions include toe, and possibly camber. Let’s look at the front: Visualize a bicycle with two front wheels — parallel to each other, rather than one. Caster is the angle of the bicycle’s front fork, viewed from the side — relative to vertical. Most vehicles have a few degrees or more positive caster, similar to a bicycle. If one wheel has less caster than the other, a pull to that side is likely.

Camber is the inward or outward vertical lean of each wheel. Positive camber is out at the top (bow-legged), and negative camber is inward at the top (squatting). Incorrect camber affects tire life as a leaning tire wears more on one side, and can contribute to a pull to one side.

Toe is a measurement of the two wheel’s parallelism, as viewed from above and is by far the most critical. Toe-in is pigeon-toed, closer at the front than back, and toe-out is the opposite. Incorrect toe will cause dramatically increased tire wear — usually wearing one side of the tires more than the other, with a feathered tread. If, when rubbing your hand across a tire’s tread, it feels smooth one way and rough the other, incorrect toe is likely.

Toe is typically adjustable; caster and camber aren’t. Aftermarket kits often allow adjustability.

It sounds like you may have some worn parts, such as ball joints, tie rod ends, control arm bushing, or upper strut mounts. The difference between minor looseness and alignment-altering wear can be a blurry call. Wear or damage is much easier to classify. In the case of safe but worn parts, one might weigh the benefits of optimum handling and tire life versus remaining time of ownership. It’s possible to check/adjust static alignment on a vehicle with worn suspension components, but the angles go askew as road forces stretch the worn joints, throwing off actual driving alignment.

Get a second opinion on the suspension parts wear to play it safe. If your tires wore well and there is no pulling, wandering or noises, your parts and alignment may not be that bad.

Brad Bergholdt is an automotive technology instructor at Evergreen Valley College in San Jose, Calif. Readers may send him email at; he cannot make personal replies.

Categories: Wire stories
TribLIVE commenting policy

You are solely responsible for your comments and by using you agree to our Terms of Service.

We moderate comments. Our goal is to provide substantive commentary for a general readership. By screening submissions, we provide a space where readers can share intelligent and informed commentary that enhances the quality of our news and information.

While most comments will be posted if they are on-topic and not abusive, moderating decisions are subjective. We will make them as carefully and consistently as we can. Because of the volume of reader comments, we cannot review individual moderation decisions with readers.

We value thoughtful comments representing a range of views that make their point quickly and politely. We make an effort to protect discussions from repeated comments either by the same reader or different readers

We follow the same standards for taste as the daily newspaper. A few things we won't tolerate: personal attacks, obscenity, vulgarity, profanity (including expletives and letters followed by dashes), commercial promotion, impersonations, incoherence, proselytizing and SHOUTING. Don't include URLs to Web sites.

We do not edit comments. They are either approved or deleted. We reserve the right to edit a comment that is quoted or excerpted in an article. In this case, we may fix spelling and punctuation.

We welcome strong opinions and criticism of our work, but we don't want comments to become bogged down with discussions of our policies and we will moderate accordingly.

We appreciate it when readers and people quoted in articles or blog posts point out errors of fact or emphasis and will investigate all assertions. But these suggestions should be sent via e-mail. To avoid distracting other readers, we won't publish comments that suggest a correction. Instead, corrections will be made in a blog post or in an article.